Yeah it took a while for me to find as well, Debian moved to managing alot of packages you used to install with pip. In many cases you can just prefix pip packages with python3- and find them via apt.
Yeah it took a while for me to find as well, Debian moved to managing alot of packages you used to install with pip. In many cases you can just prefix pip packages with python3- and find them via apt.
apt install python3-certbot :)
This is true, they have however debated the issue and might loosen the restrictions:
TL;DR and for non-swedes: the suggestion argues that hobbyists should be allowed to use metal detectors more freely. The motion was initally approved by Riksdagen but later voted against as there already work in progress on matter of simplifying the rules regarding metal detectors. So change might come, hopefully sooner than later
Probably not. It’s most likely automated scanning and the subdomains seem common enough to be included in wordlists. Another possibility is that the subdomains have leaked somehow, do you use LetsEncrypt? If so, the existence of your subdomains is public knowledge and can easily be picked up by bots.
oh and don’t run it all in one image, make one per service and use docker-compose to bring it up
Since it’s a test environment you should be fine with that amount of hardware, except for the AI stuff perhaps. That shit eats compute like nothing else, but it also depends on how much log you feed it. Go ahead and try bringing up the containers and observe how the load increase, it’s a good learning experience and perhaps one of the most difficult aspects of SIEM (sizing).
I had issues until I got connectors that come with a little sleeve that you thread the wires through before putting them into the part you clamp them in. Get those if you if you haven’t already. Also get a cable tester, they are pretty cheap
Unless if you do want containers :)
So I searched a bit and this link has a few suggestions: https://www.blister-prevention.com/blogs/prevention/holes-in-the-back-of-my-shoes
TL;DR you can have a deformity on your feet called Haglunds which can worsen wear on the heel counter. There is also a possibility that you can relace your boots or use padding to reduce wear.
It looks like you are right :( https://www.japan-guide.com/news/japan-rail-pass-cost-increase.html
Hey,
I’ve been to Japan twice, 2012 and 2017. It’s a bit difficult to estimate a budget as prices vary alot depending on what you are thinking of doing. Food for example can be decently cheap (ramen, sushi, convenience stores) but also expensive (Michelin-level dining). Back then I paid on average maybe 10-15 USD for dinner (2017). I dont remember too well and considering the global economy it might have become more expensive in general. I remember having katsudon in Akihabara for maybe 4-5 USD back in 2012 thinking it was insanely cheap for such a great meal.
Have you decided on which cities you are going to visit? I can mostly recommend places in and around Tokyo, Kyoto, Nagasaki and Hiroshima. If you are going to Okinawa I can give you a few suggestions as well.
Trains are excellent in Japan and if you are travelling between cities you should get a Rail pass. I’ve also travelled by night bus between Tokyo and Kyoto, but I would not pick them over the trains unless you opt out from getting a Rail pass. Note that you need to buy the pass before arrival in Japan!
The importance of speaking Japanese varies on the places you visist. If you mostly stay in Tokyo you will probably be fine speaking only English, but you will regularly run into people that can’t understand you. Alot of street signs have romanized text on them so you can get by decently well, but knowing Japanese helps immensely. If you travel outside Tokyo and if you visit smaller cities and villages in particular you will likely struggle without understanding Japanese.
Hmmm maybe restart Jellyfin? I know I had to tinker a bit to get it working. Also check that the hostname matches on the cert and your jellyfin config
Check the permissions of the certificate as well as the path to it. Jellyfin is running as a low priv account and probably lacks read rights.
I would be hesitant to put a squid proxy directly on the Internet as there is a history of vulnerabilities in that software and afaik a bunch of them are yet to be fixed.
First of all I would advise against trying to bypass the security controls your school implemented, but if I hypothetically would attempt to do what you’re trying I would probably set up a haproxy on a dedicated piece of hardware, such as a raspberry pi, and expose 443 to the Internet. I would configure a simple static website to serve as default, and add a ssh backend like in this guide: https://www.haproxy.com/blog/route-ssh-connections-with-haproxy
Now you can SSH to your backend by wrapping the connection with openssl s_client. From here you can do a dynamic port forwarding, which essentially acts as a socks proxy and finally connect to that with firefox
edit: slap a tls cert on that too for good measure. Helps with hiding the ssh traffic