I spent entirely way too much time trying to get one of these style extruders on my Ender 3. Maybe I picked a knock off without realizing it, maybe mine was just defective, I’m not entirely sure.
But it was ultimately the cause for my printer underextruding on certain layers. If you need a new extruder, go for something better than these cheap $20 ones and get an actually decent one.
But on the bright side, my printer is finally fixed! It feels nice to be able to get back into the hobby again.
A good solid extruder if you are willing to build it yourself (and want/need bowden), I can recommend the Voron M4 extruder.
I recently got a bltouch as well. I should have done so waaaay earlier. It’s actually allowed me to switch out those horrible and easy to bump/misalign nobs that control bed height.
Now I just have two nuts per corner holding everything down.
All printers should come with one.
I recently got a bltouch as well. I should have done so waaaay earlier. It’s actually allowed me to switch out those horrible and easy to bump/misalign nobs that control bed height.
Now I just have two nuts per corner holding everything down.
All printers should come with one.
Do you know if that can be printed in PETG?
I always saw recommendations to use ABS and I really don’t want to print that stuff
Of you don’t use it in an enclosure, yes, PETG is ok.
I bought a cheap dual drive clone a long time ago for my Ender 3 which I’m quite happy with.
One of the best upgrades I did to my CR10s was to install the microswiss extruder (the bowden replacement.)
The other two big ones are the BLTouch and the BTT board (SKR e3 mini)- mostly because I set up UBL around the same time.I bought one of these and had a lot of trouble, until i figured out when installing it I accidentally mixed up the spring from the plastic extruder and the new one. Once i swapped them it was fine.
I have Voxelab Aquila and just got the Creality Direct Drive Extruder, tell ya what it’s pretty nice
What extruder did you end up going with?
Why did you want to originally replace the extruder on your ender 3? I’ve only been running mine for ~100h now, so I haven’t yet figured why one would need to change it. Did yours just break?
The extenders on ender 3s are all sorts of trash, the bronze gear wears out pretty fast, tensioning issues, build quality.
How you have 100h on one is frankly a miracle. I have multiple ender3 s and I just immediately change out the extruder at this point.
Over 200h now. I rack up hours printing parts with 100% infill as they get annealed in the oven. Time will tell when I get issues. So far I’ve had to retighten the x axis belt once, but no other issues.
I get that the original plastic tension arms break after a while, but I hope that the metal arm on the neo will last longer. Can the softer extrusion gears be replaced with steel or some other stronger material?
They can, but really it’s not even worth it with those things, you can get cheap bag or titan extruder knockoffs on Ali- express that are a million times better. One of my Enders has a cheap titan direct drive kit and it’s actually awesome. I think I paid 35 bucks for it. And the knock off came with dual gear hardened steel gears. Triangle labs makes a killer bmg clone as well
Yeah, this is like the 4th time I’ve had to replace it.
I don’t think it’s just a matter of print time, I think it’s also a matter of how long you’ve had the machine. I’ve has mine for I think 4 or 5 years now. The tension arm on the extruder is under constant tension at all times every day. The plastic extruder Ender 3s come with is just not strong enough for the task, so they end up breaking.
I think my second one was basically and identical one made of alluminum. But that one ultimately died as well, for the same reason. So I switched to the above one, which turned out to be a mistake.
So now my 4th one is a CNCed steel dual extruder from micro Swiss. Hopefully it lasts.
I had some trouble with these cheapo extruders a while back. The key was swapping their gear wheel for my old one, which wasn’t worn out. And yes, I calibrated esteps - it just didn’t grip well. I washed it and adjusted the tension, and nada.
a lot of the amazon cheapos don’t have proper bearings on the gear, so you slowly wear out the the drive bolt. if you see gray powder forming… you have a problem. Some 3-in-1 (though I recommend the PTFE 3-in-1) will slow it down, but it’s still going to wear.
Crap, I bought one of these and it worked well for a few months, but now my printer has been under extruding for a while and I couldn’t figure out why. Do you have a better recommendation?
I’m a fan of Trianglelab’s DDB V2.1. Sure it’s fundamentally a clone, but at least they’ve made some improvements to it, and the original is really not worth the price Bondtech is charging for it.
It’s a lot stronger than the Creality extruder and the single gear “all metal” red extruder, which makes extrusions more consistent. It can also print somewhat flexible filaments, at least if you slow down a little.
There are of course better and lighter extruders out there, but the DDB has the advantage that it can be used as a drop-in replacement on Enders etc., and if you want to mod the printer in the future it’s compatible with most custom designs.
I ended up switching to this one:
https://store.micro-swiss.com/products/micro-swiss-bowden-dual-gear-extruder
I’ve heard good things about micro swiss, so hopefully this one will last.
