I’ve had these banisters in my house for ages that had this really poorly done ugle brown/maroon paint. My wife got fed up with them and decided to strip and sand them.

Wonder of wonders, what’s under there is some kind of dense hardwood with some great grain to it.

Now I’m trying to decide how to finish it.

My initial plan had been what I always do: basic stain plus a wipe on poly of some sort. Pretty good, pretty easy.

However, this is significantly higher quality wood than the cheap pine I usually work with. It was suggested to me I look into a Tung or Danish oil, and I’ve now fallen down a deep rabbit hole of wood finishing.

Any preferred finishes that emphasize grain for pretty wood in high traffic areas?

  • mailerdaemon@lemmy.world
    link
    fedilink
    arrow-up
    5
    ·
    1 year ago

    Whatever you do, test the finish first. If you can remove the piece and do a test on the bottom, do it before you commit to the entire piece.

    I’d probably do what you said, maybe use some sanding sealer first, and then stain and wipe on poly. I’ve had great success mixing poly and oil based stain 50:50 to make a wipe on finish.

    • gimlithepirate@lemmy.worldOP
      link
      fedilink
      arrow-up
      4
      ·
      1 year ago

      Wish that was an option, but whatever dingaling installed this stuff put all kinds of caulk on the bottom edge and then nailed it in…

      Somebody committed a series crime against wood with this lol. Just trying to come up with something reasonable.

      Why would you go with a stain+poly vs a finishing oil of some sort?

      • DavidP@toast.ooo
        link
        fedilink
        arrow-up
        1
        ·
        1 year ago

        Oil based poly will smell much much worse than shellac. Water based poly wouldn’t be so bad.

        • mailerdaemon@lemmy.world
          link
          fedilink
          arrow-up
          1
          ·
          1 year ago

          OP will have to deal with the smell of the stain anyway, might as well do it right and use oil based poly.

          I’ll agree that shellac is a joy to work with and looks great, but I’d be worried someone would attempt to clean the wood at some point in the future and damage the finish

          • gimlithepirate@lemmy.worldOP
            link
            fedilink
            arrow-up
            2
            ·
            1 year ago

            We’ve been dealing with the smell of citristrip this weekend lol, we can deal with the poly smells. Our house uses evap cooling which provides a ton of options for ducting air away from where the people are.

  • DavidP@toast.ooo
    link
    fedilink
    arrow-up
    3
    ·
    1 year ago

    I’d go with an oil-based polyurethane. Stain is your choice. While water based poly will have much less odor I’ve found it to be less durable.

  • ragnarokonline@vlemmy.net
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    Wish I could help ya. You definitely want a hardened finish like poly or shellac, but shellac is going to stink up your home if you can’t remove the banisters to finish.

    I’ve had a lot of luck with beeswax for a finish, but more for boxes than furniture. There are a lot of great bands out there, though you’d probably have to reapply every 6-12 months (which would get tedious)

  • torknorggren@sopuli.xyz
    link
    fedilink
    arrow-up
    2
    ·
    1 year ago

    Just go with the wipe on poly. The other oils don’t make that huge a difference, and build slower than what I would want in a high traffic area.

    • gimlithepirate@lemmy.worldOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      No idea. Hand rial is the next project. Either going to sand down finish to match, replace with something new, or paint. Undecided.

  • Moose@lemmy.ca
    link
    fedilink
    arrow-up
    1
    ·
    1 year ago

    Hardwax oil like rubio, osmo or odies seem to be the favourites when it comes to higher end stuff, you can apply maintenance coats and/or repair fairly easily from what I heard.

    Whatever you do, you should do the same with the handrail, it’ll clash of they don’t match

    • gimlithepirate@lemmy.worldOP
      link
      fedilink
      arrow-up
      1
      ·
      1 year ago

      That’s part 2 of this project. We will see, the hand rails are not in great shape. May replace, or paint them. The banisters have more visual impact anyway, and are a significantly nicer wood.

  • satterle@lemmy.ca
    link
    fedilink
    arrow-up
    1
    ·
    1 year ago

    I’d suggest either oil or water poly. Hardwax oil and other oils require ongoing maintenance, like once a year. Shellac is also a great finish but is not recommended for high traffic areas.