I have recently obtained a friend’s old Formlabs Form 2 SLA printer. I I am an absolute beginner to printing, but I am pretty excited to get into it.

However, the only place that I would realistically be able to put it is on my desk in my bedroom. From everything I’ve read, I need a better ventilated space with more tolerance for a mess than I could possibly provide.

I think that the right call is to just sell it and save up for some FDM printer, but at the end of the day, I have the SLA printer in hand.

I am asking whether these concerns about resin printers are really that bad and if I am actually fine to start learning printing with what I have in my bedroom.

  • Prunebutt@slrpnk.net
    link
    fedilink
    English
    arrow-up
    35
    ·
    edit-2
    7 months ago

    I tried this once and decided thhat it’s too risky. Do not do this.

    Rsein printers are not for bedrooms. You’ll constantly smell that stuff and think that you’re poisoning yourself. Also: spills will happen and you don’t want that stuff spilled on your regular desk or on some object of daily use which then needs to be put out in the sun, just to be safe.

    • kakes@sh.itjust.works
      link
      fedilink
      English
      arrow-up
      11
      ·
      7 months ago

      Gonna second this. Unless you also install a 24/7 fume hood in your bedroom, the smell alone would be nauseating - not to mention toxic/carcinogenic.

      Also, I don’t have an FDM printer, but I’ve heard even those aren’t good for bedroom use due to the fumes from the plastic.

    • littleblue✨@lemmy.world
      link
      fedilink
      English
      arrow-up
      6
      ·
      7 months ago

      This. I started with FDM at my computer desk in my bedroom. The noise is one thing, but I moved to resin and took the whole lab downstairs. Even in that space, without proper ventilation? I tried it once, and immediately put up the vent system I had on hand.

      Simply put? It’s a non-zero risk that isn’t worth it. Hell, there might even be someone here that’s close enough to print stuff for you until you can set something up yourself. 🙌🏽

    • SzethFriendOfNimi@lemmy.world
      link
      fedilink
      English
      arrow-up
      3
      ·
      edit-2
      7 months ago

      I will say for ABS this can be mitigated with the following:

      • An enclosure (I use a comgrow grow tent)
      • Not opening the printer enclosure for at least 20 minutes (so the airborne particulates settle down)
      • A replaceable carbon filter (I built a Nevermore duo and bought some activated Charcoal to refill it with)

      After doing the above I don’t smell fumes at all. In fact I run the Nevermore even with PLA just to capture any micro particles since the charcoal is easy enough to replace.

      Even so, as cool as Resin looks, I’m not having that stuff inside my house with my family. If I did it would have to be in a garage that’s vented but I have a carport and there’s no way I can regulate the environment (temp, humidity) for decent prints. So for now I’m just going with FDM

      • EmilieEvans@lemmy.ml
        link
        fedilink
        English
        arrow-up
        2
        ·
        7 months ago

        Styrol isn’t a particle that settles down like dust. It is a liquid with a significant enough vapor pressure to be problematic.

        An activated carbon filter can get rid of the vapor.

  • AliasVortex@lemmy.world
    link
    fedilink
    English
    arrow-up
    8
    ·
    7 months ago

    Chiming in to say that you absolutely don’t want that in your bedroom. Not sure how ubiquitous the experience is, but if you’re ever done a titration experiment in a chemistry class (the one where you add one solution into another a couple drops at a time), your body’s response to being exposed to resin fumes (as well as VOC’s from some of the more exotic fdm materials like ASA) is a lot like that: little by little you add more of one solution to the other and at first you don’t really notice anything (beyond the volume increase), so you keep on adding more, when you finally hit the equilibrium point the whole solution suddenly changes colors.

    In practical terms, the more you’re exposed to resin VOC’s the more you’ll burn through your buffer, once it’s gone your body will basically go into panic mode whenever it comes into contact with said material. It’s one of those things that’s high enough on the fuck around side of things that you really don’t want to find out…

    That said, welcome to 3D printing! There’s plenty of resources around, so (for the most part) if you aren’t sure about something or run into trouble, all you have to do is ask!

  • alkheemist@aussie.zone
    link
    fedilink
    English
    arrow-up
    7
    ·
    7 months ago

    Yes, it really is that bad. We have a resin printer at work and it has been banished to a different room due to the resin fumes. The table it sits on is perpetually sticky, and we go through twice as much IPA postprocessing the prints than we use in resin

  • William@lemmy.world
    link
    fedilink
    English
    arrow-up
    6
    ·
    7 months ago

    I have plenty of space, and I still sold off my resin printer because of fumes, mess, and general headaches. I don’t recommend it if you aren’t fully prepared for what it requires to do it safely and sanely.

  • EmilieEvans@lemmy.ml
    link
    fedilink
    English
    arrow-up
    4
    ·
    7 months ago

    Form 2 is challenging to operate for a newbie:

    • laser -> “special” resin required. Formlabs recently moved on to LCDs meaning in the years to come the last third-party manufacturers will stop producing those resins as demand further declines. Leaving the first-party FormLabs as the only option ($100+/kg).
    • Difficult to maintain resin tank. Requires a vacuum oven and an upfront investment of roughly $150 for chemicals. There are conversion kits/prints for FEP film to resolve this limitation.
  • admin@lemmy.cringecollective.io
    link
    fedilink
    English
    arrow-up
    5
    arrow-down
    1
    ·
    7 months ago

    I converted the closet to a 3D Printing area, adding a bathroom-style ceiling vent fan and shelf to hold the 3D printer, resin, cleaner and accessories.

    I will tell you I can’t smell anything with the doors shut, and the vent does a good job of removing the smell during printing.

    Can’t recommend TeachingTech’s “Resin 3D printing beginners step by step guide” enough, that was basically the model I followed, including hanging paper towel holders on the inside doors and getting silicone mats to prevent spills.

    Also, gloves. Every time. Every time I open that closet the first thing I do is put on gloves, even to touch the tools. I have no idea what still has resin on it, so I trust nothing in there.

  • Honytawk@lemmy.zip
    link
    fedilink
    English
    arrow-up
    2
    arrow-down
    1
    ·
    7 months ago

    It also isn’t just the resin fumes that are toxic, but the post processing bio ethanol as well.